四、auto dial / access and hangup codes
译者注:此部分与基本功能无关,暂不翻译。
五、manual interconnect access and hangup codes
译者注:此部分与基本功能无关,暂不翻译。
六、format scan lists
译者注:此部分与基本功能无关,暂不翻译。
七、format selectable pl
译者注:此部分与基本功能无关,暂不翻译。
附录一 saber models
型号范例:
h a b cc d e f g h i j
请将上述字母与下面对照。
h=handheld
1、a=4,高功率;
a=3,低功率。
2、b=2,68-88mhz
b=3,vhf
b=4,uhf
3、cc=sa,标准手持机
cc=qx,有声音保密功能
cc=yb,防水的
cc=yx,防水带声音保密功能
4、d=n,无键盘
d=j,三个按键
d=k,全键盘
d=g,saber ie(2 zones,无屏幕)
5、e=7,core为二进制(数字)(美版)
e=7,core为音频(模拟)(国际版)
6、f=1,宽带
f=5,12.5或窄带(国际版)
7、g=0,10频道(国际版)
g=3,12频道
8、h=9,版本变更
附录二 options list and definitions
h251 - 60 second tot
60秒发射超时。
h901 - non-standard tot
非标准发射超时。
silent monitor
主要用于带哑音的电台。按下电台侧面的监听键时,如果载波进入你当前监听的频道,音频不会被忽略。
h384 - muting via keypad
允许你使用按键忽略警告音。
h153 - omit all tones
禁止电台产生任何的警告音或侧音,电台的音频反馈会被禁止。该项与h619冲突。
h365 - transmit inhibit on busy channel
繁忙禁发。如果尝试发射会产生警告音,该项也会禁止监听建。
注意:仅以载波静噪的频道上,该项不起作用,即使该频道处于繁忙状态。同时,监听按钮也会在所有频道中被关闭。
h359 - channel busy led
选择该项后,低电压警告会失效(与h906冲突)。在有载波时,led闪烁。
h906 - low battery led
低电压时led灯闪烁,该项与h359冲突。
safe battery (h155, h200, h237, h759)
该项对于saber i不会显示,只设置h906即可提示低电压。
h958 - unit id - mdc 600
发送mdc 600信令,可以标示一个unit id。可以设置前、后和前后都有三种发送方式。发送时会有侧音提示(如果开启侧音的话)。secure版本不能设置后信令。
h959 - unit id - mdc 1200
发送mdc 1200信令。其余同h958。
h961 - unit id and emergency - mdc 600
按下紧急按钮后,会在预设定的紧急频道发射mdc 600 unit id和警报。
h962 - unit id and emergency - mdc 1200
发射mdc 1200 unit id,其余同h961。
h963 - unit id w/ audible emergency - mdc 600
可以在发射mdc 600信令、警告的同时产生侧音(本机喇叭响),其余同h961。
h967 - unit id w/ audible emergency - mdc 1200
发射mdc 1200信令,其余同h963。
h923 - unit id w/emergency revert - mdc 600
发射mdc 600 unit id,在预设的频道发射一个静默的报警音,然后回到发射警报前所在的频道守候。
h946 - unit id w/emergency revert - mdc 1200
发射mdc 1200 unit id,其余同h923。
no channel re-revert after emergency
selecting this option will cause the radio to remain on the reverted channel after the completion of the emergency packet transmissions. any subsequent transmissions will be sent out the assigned emergency revert channel. cancelling this may be done by manually changing channels or by resetting the radio.
h770 - pretime delay - 300ms
发射mdc信令前300ms延迟。默认是500ms。该项与h771、h779冲突。
h771 - pretime delay - 700 ms
发射mdc信令前700ms延迟。
h779 - non-standard pretime delay
发射mdc信令前的非标准延迟。
h619 - omit side tones
忽略侧音(特别指mdc信令发射时的长鸣侧音,而非警告音)。该项与h153冲突。
h371 - zone and channel operation
zones可以通过按键来切换,频道可以通过频道旋钮来选择。每个zones可以存储12个频道。
h396 - channel only operation
此项可以定义一个只有频道(没有zones),通过按键选择频道的电台。
h560 – talkaround
selecting this option will allow talkaround on a saber ie. data for one zone can be entered in the channel information screen. this option is incompatible with option h256 (two zone operation).
h256 - two zone operation
该项可以允许在saber ie上存在2个zones。
h346 - zone display names
显示zone名称
h380 - channel display names
显示频道名称
h368 – autodial
this option adds autodial capability to the radio. you can specify up to 9 telephone numbers along with their access and hang-up codes for each phone number and zone/channel number on which the call will be made on. this option is available on c model radios only. a and b model radios can have only one access and hang-up code. you will not be able to change the telephone numbers, and access and hang-up codes using the keypad. in order to modify this information, you will have to use the radio service software.
h669 - omit inadvertent lock
inadvertent lock is a standard menu option for display models. this option will disable the inadvertent lock which allows you to lock out the keypad temporarily during periods of non-usage, or for safety purposes to minimize inadvertent actuation.
h670 - omit memory (2k memory option)
this option is necessary for saber ii's with a 2k eeprom instead of the normal 8k. it is important to ensure that the size of the codeplug that is being created does not exceed the bounds of hardware in the radio. selecting this option will reduce the number of available options.
h297 - manual telephone interconnect
this option allows manual dialing of dtmf telephone numbers. in this feature, you may fix the length of the tones transmitted, or you may select manual length tones.
h397 - menu lock
this option will add a menu lock to the radio. with this option you can lock out the keypad from unauthorized users unless the proper password is entered. the password menu is also included in the radio to allow the capability of changing passwords. the default password is the null password which is entered by pressing the enter key on the radio. you must select option h669 - omit inadvertent lock, to enable this option.
h345 - radio lock
this option will allow you to lock the radio when it is first turned on. in order to enable any radio functions or menus, the correct password must be entered otherwise the radio will be inoperable and none of the options or menus can be accessed. the same password in option h397 - menu lock, will be used here for a and b model radios. for c model radios, menu lock can have different passwords if you wish.
h273 - operator selectable scan
此项允许你维护一个扫描列表,使用电台上的按键而不是rss。
h344 - mode slaved scan (仅针对saber ii和saber iii)
选择该项会提供你10个扫描列表,每列表中有13个条目。13个频道中,有2个优先扫描信道,10个非有限扫描信道,1个可定制的传输信道。
译者注:本条目资料过于冗长,不再翻译。
h444 - delete proper code detect
该项开启电台会忽略所有信号,但是不会忽略加密的信号。
h245 - delete clear mode alert tones on transmit
该项会删除所有用于指示电台处于明码发射状态的警示音。这个警示音的频率是820hz,时长为80ms。你知只能通过rss忽略这个音。
h244 - delete clear coded transmit switch
如果你的电台型号是secure型号(可加密),而又没有一个用于明码/密码转换的开关,你必须打开这个选项。如果你的电台不是secure型号,你不必理会这个选项。该选项与h400冲突。
h400 - secure voice slaved to a mode
如果一个频道是加密的,那么电台会以一致的方式传输。一个“开关位置错误”提示音会发出,如果明码/密码开关处于明码(clear)位置上。该项与h244冲突。
h401 - clear voice slaved to a mode
如果一个频道是明码,电台会以一致的方式传输。一个“开关位置错误”提示会发出,如果明码/密码开关处于密码(secure)位置上。
h432 - vp capable only
该项仅在电台拥有dvp调制,但是没有安装加密模块时打开。电台只能在明码/密码开关处于明码位置时传输,处于密码位置时,电台会发出连续的错误音。如果h244被打开,开关的位置是被忽略的,始终以明码传输。h432打开后,开机时会有一声短促的提示音。
zero audio enable
音量在用户设定水平以下,会被电台静音。
quik- call ii™
quik- call ii™是一个联合了2音信令和编码的接收功能。quik- call ii™的频率在288.5hz到2469hz之间。h365与该项冲突。
h701 - individual call
选择该项必须选择quik- call ii™。个别呼叫使用2音信令,次序为先a后b。a音和b音频率不能相同。该项与h702和h703冲突。
h702 - two-tone group call
两音组呼,基本功能同h701。
h703 - long tone b group call
长音b组呼,基本功能同h701。
h167 - timed auto reset
to select this option you must select the quik call ii option. this option allows you to enter the time after which the radio goes back to quik call decode mode (i.e., after decoding quik call in the quik call decode mode). in addition, transmitting while in the quik call decode mode resets the timer at the end of the transmission. the valid range is 1 - 290 seconds (a default of 5 seconds is set if this option is selected). this option will be selected automatically if option h188 is selected. if this option is not selected, the radio will be in manual reset mode: you can manually force a reset by momentarily depressing the monitor button.
h188 - carrier override timed auto reset
to select this option you must select the quik call ii option. this option is used in conjunction with option h167 (timed auto reset). you can enter a value ranging from 1 to 290 seconds (a default of 5 seconds is set if this option is selected), in case option h167 is not already selected. if you select this option, the timer is reset at the end of the carrier. this is in addition to the characteristics described for h167.
singletones - general (ptt/rats)
this is the most flexible option out of all the three single tone options. when selecting this option, two windows will pop-up in sequence. enter a frequency in each of these pop-up windows. both of these tones can be transmitted through any of the three transmit switches (ptt/rat1/rat2). the valid range for these two frequencies is from 300 hz to 3000 hz in increments of 1 hz. this option is a non-numbered option.this option is incompatible with the following options.
h707 - 1 tone singletone via ptt button
h742 - 2 tone singletones via rat buttons
the following options are enabled if you select this option:
singletone non-std. pretime
singletone time duration
h619 -omit mdc side tones
h707 - 1 tone singletone via ptt button
when selecting this option a pop-up window is displayed and you are asked to enter a frequency for single tone1. if h707 is enabled, rat1 and rat2 buttons are disabled and single tone1 is sent out through ptt on all channels. this option is incompatible with all the mdc unit id (ptt) options. the valid range for single tone1 is from 300 hz to 3000 hz in increments of 1 hz. this option is incompatible with the following options:
singletones - general (ptt/rats)
h742 - 2 tone singletone via rat buttons.
all the mdc unit id (ptt) options.
the following options are enabled if you select this option :
singletone non-std. pretime
singletone time duration
h619 -omit mdc side tones
h742 - up to 2 singletones via rat buttons
this option is very similar to the singletone - general option. when selecting this option two pop-up windows are displayed on the screen sequentially. enter a frequency in both the windows. if this option is enabled and none of the mdc unit id options are selected then signalling on ptt is disabled. if this option is selected along with any of the mdc unit id options then mdc unit id is sent out via ptt. single tone1 is sent out through rat1 and single tone2 is sent out through rat2. you may leave the default single tone 2 frequency, in case you need only one single tone.this option is incompatible with the following options:
singletone - general (ptt/rats)
h707 - 1 tone single tone via ptt button
multiple repeater access codes - mdc 600
multiple repeater access codes - mdc 1200
the following options are enabled if you select this option:
singletone non-std. pretime
singletone time duration
h619 -omit mdc side tones
本文来自csdn博客